|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
folding mirror not working
|
|
10-06-2013, 10:56 PM | #1 |
Lieutenant
43
Rep 420
Posts |
folding mirror not working
ok so yesterday i did a coding in NFRM to turn on low beam on when unlock. some reason it didnt work right so i went expertmode and got back to default. now my folding mirror wont work with switch where its located with windows switch.....is there a coding to turn my mirror back on? i couldnt find them...thanks
|
12-05-2014, 06:59 AM | #9 |
Colonel
163
Rep 2,399
Posts |
i have same problem! i installed frm2 into my car to have welcome lights, it looks all coding is ok but now my mirrors will not work at all. no movement from switch at all no heated or folding. can anyone help with ideas?
|
Appreciate
0
|
12-08-2014, 04:36 PM | #10 | |
First Lieutenant
41
Rep 328
Posts |
Quote:
Did you copy the vo from cas to nfrm? If you have a pre-lci you should simulate the date (#0307) because than you can pick nfrm from the modules list iso frm. |
|
Appreciate
0
|
12-09-2014, 03:18 AM | #11 | |
Colonel
163
Rep 2,399
Posts |
Quote:
|
|
Appreciate
0
|
12-09-2014, 04:28 PM | #13 |
First Lieutenant
41
Rep 328
Posts |
|
Appreciate
0
|
12-09-2014, 06:32 PM | #14 |
Colonel
529
Rep 2,503
Posts |
Teq, cryptomit
I'm glad you came up on this thread. I tried to help cupraraj remotely and everything seems in order, maybe I missed something though. I've never seen this problem after FRM upgrade... For active LIN bus is; ASP_LIN_VERBAUT aktiv ???? In which case I believe I checked this and it was aktiv. Was there some pin change on FRM2 for LIN bus? Pin 22, 23 for drivers door cluster and passenger mirror? This problem is really bugging me and it's not even my vehicle lol!!!! One thing I noticed I'd actual date in VO has been written to VO in CAS and NFRM, rather than just simulating? Could this cause a problem on LIN BUS? |
Appreciate
0
|
12-10-2014, 03:19 AM | #15 |
Colonel
163
Rep 2,399
Posts |
|
Appreciate
0
|
12-14-2014, 02:13 PM | #17 |
Lord Scrip
1823
Rep 3,018
Posts
Drives: 2011 M3 Coupe
Join Date: Jan 2012
Location: LA,Ca
|
I found the best thing to do is take a backup before changing the PSW! if you haven't after modifying the coding and stuff isn't working properly there is something you can try. It is dependent that you VO is accurate for your car! In NCSExpert do a "SG_RESET".....Then change the job to "SG_CODIEREN" but make sure your "PSW" file in C:\NCSExpert\WORK is completely empty. This codes nothing into the module which makes the car update the module based off equipment and VO. You may have to recode custom stuff back but the FRM will be setup to your car properly which should re-enable your mirror.
|
Appreciate
0
|
12-16-2014, 03:48 PM | #18 |
First Lieutenant
41
Rep 328
Posts |
Wiring for the lin bus is the same.
Frm2: X14260 pin 22: outside mirror passenger's side lin bus pin 23: driver's switch cluster Are you sure that the frm2 isn't broken? |
Appreciate
0
|
12-17-2014, 08:06 AM | #19 |
First Lieutenant
41
Rep 328
Posts |
|
Appreciate
0
|
12-17-2014, 08:32 AM | #20 |
Colonel
163
Rep 2,399
Posts |
|
Appreciate
0
|
12-17-2014, 03:57 PM | #21 | |
First Lieutenant
41
Rep 328
Posts |
Quote:
Uhm...blocking? Remove glovebox? I've got a customer who also wants this but I'm going to install it in about 2 monts. I don't expect that their will be issues with it. Please check the fuse and report back. |
|
Appreciate
0
|
Bookmarks |
|
|